收藏本站
Micrel Inc.
Functional Description
The MIC4811 is a six channel linear WLED driver. The
WLED driver is designed to maintain proper current
regulation with LED current accuracy of 1%, and typical
matching of 1% across the six channels. The WLEDs
MIC4811
R SET
The R SET pin is used to set the peak current of the linear
driver by connecting a R SET resistor to ground. The
average LED current can be calculated by equation (1):
are driven independently from the input supply and will
maintain regulation with a dropout of 100mV at 50mA.
The low dropout allows the WLEDs to be driven directly
from the battery voltage and eliminates the need for
large and inefficient charge pumps. The maximum
R SET [k ? ] = ( 820 / I LED [mA] ) + 0.139
A plot of I LED versus R SET is shown in Figure 2.
(1)
WLED current for each channel is set by the external
R SET resistor. Dimming is controlled by applying a PWM
signal to the END pin. The MIC4811 accommodates a
1000
Peak LED Current
vs. R SET
wide PWM frequency range as outlined in the application
information section.
100
Block Diagram
As shown in Figure 1, the MIC4811 consists of six
current mirrors set to copy a master current determined
10
by the R SET resistor. The linear drivers have a
designated control block for enabling and dimming the
WLEDs.
1
1
10 100
1000
V IN
RSET (k ? )
The input supply (V IN ) provides power to the linear
drivers and the control circuitry. The V IN operating range
is 3V to 5.5V. A bypass capacitor of 2.2μF should be
placed close to input (VIN) pin and the ground (GND)
D1-D6
Figure 2. Peak LED Current vs. R SET
pin. Refer to the layout recommendations section for
details on placing the input capacitor (C1).
EN
The EN pin is equivalent to the enable pin for the linear
drivers on the MIC4811. It can also be used for dimming
using a PWM signal. See the PWM Dimming Interface in
the Application Information section for details. Pulling the
END low for more than 20ms puts the MIC4811 into a
low Iq sleep mode. The EN pin cannot be left floating; a
floating enable pin may cause an indeterminate state on the
outputs. The first pulse on the EN pin must be equal or
greater to 60 μ s to wake the part up in a known state. This
equates to 3.3kHz PWM signal at equal or greater than 50%
duty cycle. Higher PWM frequencies may be used but the
first pulse must be equal or greater than 60 μ s.
The D1 through D6 pins are the linear driver inputs for
WLED 1 through 6, respectively. Connect the anodes of
the WLEDs to V IN and each cathode of the WLEDs to D1
through D6. When operating with less than six WLEDs,
leave the unused D pins unconnected. The linear drivers
are extremely versatile in that they may be used in any
combinations, for example D1 thru D6 leaving D5
unconnected or paralleled for higher current
applications.
GND
The ground pin is the ground path for the linear drivers.
The current loop for the ground should be as small as
possible. The ground of the input capacitor should be
routed with low impedance traces to the GND pin and
made as short as possible. Refer to the layout
recommendations for more details.
April 2011
7
M9999-041411-B
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MIC4812YMME IC WHITE LED DVR HC 6CH 10MSOP
MIC5011YN IC DRIVER MOSF HI/LOW SIDE 8-DIP
MIC5013YN IC DRIVER MOSFET HI/LO SIDE 8DIP
MIC5014YN IC DRIVER MOSFET HI/LO SIDE 8DIP
MIC5016BWM IC DRIVER MOSF DUAL HI/LO 16SOIC
MIC5018YM4 TR IC DRIVER MOSFET HI SIDE SOT143
MIC5020YM IC DRIVER MOSF LO SIDE HS 8-SOIC
MIC5021YN IC DRIVER MOSFET HI SIDE HS 8DIP
相关代理商/技术参数
MIC4811YMM TR 功能描述:LED照明驱动器 High Current Six Channel WLED Driver w/ DAM and Ultrafast PWM Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC4812 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Current 6 Channel Linear WLED Driver with DAM? and Ultra Fast PWM? Control
MIC4812_1104 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Current 6 Channel Linear WLED Driver with DAMa?￠ and Ultra Fast PWMa?￠ Control
MIC4812YMME 功能描述:LED照明驱动器 High Current Six Channel WLED Driver w/ DAM and Ultrafast PWM Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC4812YMME TR 功能描述:LED照明驱动器 High Current Six Channel WLED Driver w/ DAM and Ultrafast PWM Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC4826 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Input Voltage, 160VPP Output Voltage, EL Driver
MIC4826_09 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Input Voltage, 160VPP Output Voltage, EL Driver
MIC4826BMM 功能描述:IC EL DRIVER 160VPP OUT 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01